Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across Upland
Electric gate repair in Upland typically runs $195 to $485 for most mechanical and electrical diagnostics, and we’re usually at your gate within a day of your call. If you live off the north end of Euclid, along 16th Street, or up in the 91784 foothill neighborhoods, you already know what Santa Ana winds do to heavy iron gates. We’re Manor Gate Repair, and we work on the brand you already have, from diagnosis to installation. Call (844) 703-6053 for a free estimate, and we’ll send a specialist who knows Upland gates, not a generalist guessing at your operator board.
Why Manor Gate Repair Is Upland’s Preferred Electric Gate Repair Company
Upland homeowners and property managers call us because most gate companies here are either tied to one manufacturer or they’re handymen who take on a gate job between fencing work. We’re neither. We service nine major automation brands, LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so the answer to “do you work on my gate?” is yes before you even finish the question. That matters in Upland, where a 1960s ranch on a Euclid side street may have a completely different gate setup than a 6,000-square-foot foothill estate in 91784.
Nelson Pryce leads our team, and his standard is simple: your gate, restored to spec. We diagnose control boards, operators, sensors, and keypads that general repair services won’t touch. When a gate fails in Upland, it’s almost never one clean problem. It’s a hinge anchor that loosened during a dry wind event, a limit switch that drifted out of calibration, and a keypad that’s been sun-baked for 15 summers. We handle all of it in one visit when possible, because you shouldn’t have to coordinate three different contractors to make one gate work.
Our Electric Gate Repair team knows the difference between a gate that needs adjustment and one that needs a post reset. Most companies reach for the quote book when they see a sagging iron gate. We reach for a level and a tape measure first. The right fix, not the easy upsell.
Styles & brands we work with
Electric Gate Motor in Upland
Electric gate motor repair in Upland usually costs between $235 and $520, depending on whether we’re rebuilding the operator on site or replacing a failed capacitor, gear, or limit switch assembly. A gate motor here works harder than it does in most of the Inland Empire, because Upland’s dry summer heat bakes the housing and winter rains push moisture into every seal that’s started to crack. We pull the cover, test the motor windings and control board, and tell you honestly whether the operator has life left or whether replacement is the smarter spend.
Underground Operator Repairs
Many foothill properties in 91784 run LiftMaster or FAAC underground slide gate operators, and these fail in a specific Upland way. Dry summer dust and grit pack into the rack and pinion, then the operator loses travel calibration and starts slamming or stopping short. We clear the rack, re-set the travel limits, and replace any pinion gears that have worn down. This is exact work, not a parts swap.
Limit Switch and Control Board Diagnosis
When a gate motor won’t stop at the right spot, or it reverses for no reason, the limit switches and control board are the first suspects. Upland’s temperature swings, hot afternoons and cool nights, accelerate solder joint failures on older boards. We test components individually rather than quoting a full board replacement by default. If the board is dead, we can often source the exact replacement same-week for DoorKing, Elite, LiftMaster, and the other brands we service.
Gate Access Control in Upland
Gate access control repair in Upland typically costs $185 to $450, covering keypad programming, intercom repair, remote control pairing, and safety sensor alignment. Your access control is where security actually lives. A gate that opens for anyone with a working remote isn’t much of a gate. In Upland’s estate neighborhoods, where gates protect long driveways and homes set back from the street, we see a lot of outdated keypads and intercoms wired into gate systems that have been upgraded twice since the keypad was installed. We match new components to existing systems, so you’re not paying to replace everything just because one keypad failed.
Keypad and Remote Pairing
If your keypad works intermittently or only from certain angles, the problem is usually sun damage to the keypad membrane or a receiver that’s drifted off frequency. We test the signal path first, then recommend the fix that restores function without replacing the entire system. Most keypad and remote repairs in Upland are completed in under an hour on site.
Entrapment Protection and Safety Sensors
Every automated gate in Upland must meet UL 325 entrapment protection standards, which means photo eyes and safety edges that stop and reverse the gate when something’s in the path. We see a lot of sensors that were never properly aligned after a wind event knocked the gate out of square, or that are crusted with dust from months of dry weather. We test the reversal force, align the photo beams, and verify that your gate stops safely, because this isn’t a convenience feature. It’s a legal requirement and a real safety issue.
Trusted Brands We Service in Upland
We work on LiftMaster operators more than any other brand in Upland, simply because they were the default spec on so many foothill estates built in the 1980s and 1990s. DoorKing and Elite are common on properties that use telephone-entry systems, and we see Mighty Mule on plenty of ranch-style homes where the gate was a later addition rather than original construction. Because we stock common replacement parts for all of these brands, we don’t have the “we’ll order it and come back in two weeks” problem that slows down single-brand dealers. When you call about a dead operator, we bring the parts that fix 80 percent of failures on the truck.
See the difference
Before
After
Before
After
Before
AfterCommon Electric Gate Repair Problems We See in Upland Homes
- Wind-racked gates out of square. After a Santa Ana night, the heaviest swing gates in the north-end canyon neighborhoods sag or bind because the hinge anchors have loosened in aging masonry or shallow post footings. The gate isn’t broken; the post footing is the problem.
- Underground operators packed with dust. LiftMaster and FAAC slide operators seize or lose travel calibration when months of dry inland dust accumulate in the rack and pinion. This is one of the most common calls we get from 91784 properties with long driveway gates.
- Wood gates that swell and bind. Mid-century ranch neighborhoods near downtown and along Euclid have plenty of original 1950s and 1960s wood gates. They crack and warp through hot, dry summers, then swell against the hinge post during winter rains and the operator strains against the binding.
- Control boards dead from sun and heat cycling. Upland’s temperature swings put real stress on oscillator and relay components. A board that worked fine in May can fail in November because months of expansion and contraction have fractured a solder joint.
Pricing for Electric Gate Repair in Upland, CA
Here’s what electric gate repair in Upland actually costs. Diagnosis runs $85 to $145, which is credited toward the repair when you approve the work. Keypad and remote pairing is typically $185 to $300. Safety sensor replacement and alignment runs $220 to $410. Control board replacement lands between $300 and $650, depending on the brand and board complexity. Underground operator repairs run $350 to $700, which includes rack cleaning, gear replacement if needed, and travel calibration. Every price is quoted and agreed before we start work, so the invoice doesn’t surprise you after the fact. Call (844) 703-6053 and we’ll give you a free estimate over the phone, based on what you’re seeing and hearing at the gate.
We Also Serve Cities Near Upland
Our Electric Gate Repair in Upland coverage extends naturally into the surrounding foothill and valley communities. We work regularly in San Antonio Heights, where the wind exposure is similar to 91784, and in Claremont, Montclair, and Rancho Cucamonga, where gate systems run from original mid-century hardware to newer automation. If you’re a property manager with gates in more than one of these cities, one call covers all of them.
Serving Upland, CA — Our Local Coverage Area
We’re based in the Upland area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Upland
In Upland it’s usually the post, not the gate. Santa Ana winds funnel through the north-side canyon neighborhoods and loosen hinge anchors set in aging masonry or shallow post footings. After a wind night in the foothill streets off the north end of Euclid, our tech found a 12-foot custom wrought-iron swing gate sagging because the hinge post footing had shifted in shallow soil. We re-set the post with a deeper concrete footing, corrected the sag, and re-calibrated the LiftMaster operator’s limit switches so the gate ran true again. The homeowner said it hadn’t closed that smoothly in years. Call (844) 703-6053 and we’ll tell you over the phone whether your sag sounds like a post problem or a hinge problem.
91784 sits directly under the Santa Ana wind funnel that drops out of the San Gabriel Mountains and pushes dry, gusty air through the north-side canyon neighborhoods. Those gusts hit heavy custom iron gates at full force and slowly work hinge anchors loose over repeated wind events. A gate that’s racked out of square strains the operator, wears limit switches, and eventually damages the post. Re-setting the post with a deeper footing and correcting the gate’s square is a standard repair for us in this ZIP code.
Yes, we service LiftMaster, FAAC, and other underground slide gate operators throughout Upland. The typical failure here is dust-related: dry summer grit packs into the rack and pinion, the operator loses travel calibration, and the gate starts slamming or stopping short. We clear the rack, replace worn pinion gears, and re-calibrate travel limits. Underground operator repair in Upland runs $350 to $700. Call (844) 703-6053 for a free estimate on the phone.
Yes, every automated gate in Upland must meet UL 325 entrapment protection standards, which means working photo eyes or safety edges that stop and reverse the gate if something’s in the way. We test reversal force, align photo beams, and verify that your gate stops safely on every service call where the operator or sensors are involved. If your gate doesn’t have working entrapment protection, we’ll flag it and fix it as part of the repair.
Yes, we match new keypads, intercoms, and remote receivers to your existing operator, regardless of brand. Upland properties often have DoorKing or Elite telephone-entry systems wired into older gate operators, and replacing the whole system isn’t necessary when one component fails. We test the signal path, identify the compatible replacement, and install it same-visit when the part is available locally. Call (844) 703-6053 and describe what’s on your gate; we’ll tell you what’s compatible before we come out.
Written by Nelson Pryce, Owner at Manor Gate Repair, serving Upland and the surrounding foothill communities.