Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Rialto, CA
Gate installation in Rialto usually costs between $1,800 and $6,500 for a complete automatic driveway gate, and most projects take two to four days once parts arrive. We lead with installation because Rialto’s housing stock creates specific demands: wide driveway openings on 1980s – 2000s tract lots, block-wall or wood fences that need structural reinforcement, and original builder-grade gates that are now failing at the same time across entire neighborhoods. If your current gate is sagging, rusted through, or no longer matches how you use the property, call Manor Gate Repair at (844) 703-6053 for a free measure and written quote.
Why Rialto Homes Are Different
Rialto’s building boom from the 1980s through the 2000s left thousands of homes with iron and steel gates that are now hitting end of life simultaneously. Drive down almost any street in the 92376 or 92377 ZIP codes and you’ll see the same hinge failure repeated house after house, because the original posts were often set shallow in sandy soil that shifts with seasonal moisture. Wide driveway openings, side-yard security gates, and the Inland Empire’s summer heat all combine to warp metal, dry out wood, and accelerate rust at connection points. Santa Ana winds add lateral stress that loosens post bases over time, and the rare but intense winter rains push moisture into existing rust pockets and cause post bases to heave or settle. In practice, that means a Rialto gate repair is more often a welding and post-correction job than a simple latch adjustment, and installation work needs deeper footings than a standard tract home might have gotten in 1985.
Styles & brands we work with
Our Main Rialto Services
Rialto homeowners call us most often for two things: mechanical repair on gates that have started sagging or binding, and electrical repair on automated systems that have stopped responding. Both are covered below with links to their dedicated Rialto pages.
Gate Repair in Rialto
Mechanical gate repair in Rialto means addressing what the climate and soil do to steel and iron over decades. We replace worn hinges, re-weld cracked joints on site, correct sagging posts, and straighten frames that have twisted under heat and wind load. Because many original posts in Rialto were set shallow in sandy ground, we often dig out, re-set, and re-anchor the post rather than just patching the visible symptom. For full details on repair scope, pricing, and response times, see our Gate Repair in Rialto page.
Electric Gate Repair in Rialto
Electric gate systems in Rialto face a different set of problems: heat-soaked control boards, sensors knocked out of alignment by wind or settling posts, and operators that have burned through gears after years of fighting a sagging gate. We diagnose the actual fault across LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems, then repair the component that failed rather than replacing the whole system. For the full breakdown of electrical diagnostics, operator repair, and safety-edge work, visit our Electric Gate Repair in Rialto page.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Gate Installation in Rialto
A new gate installation in Rialto solves a specific problem: the original 1980s – 90s builder gate on your wide driveway has reached the end of its service life, and patching it again costs more than starting with a properly engineered system. We build for Rialto’s conditions from the first step: footings deep enough to resist sandy-soil shifting, steel or iron frames designed for Inland Empire heat cycling, and operators matched to the actual weight and cycle needs of your opening. Every installation includes a written quote agreed before work starts, and we coordinate the full scope from post setting to final programming, so you don’t manage multiple contractors. For details on the full installation process, see our Gate Installation service hub.
Automatic Gate Installation
Signs you need it
Your current gate is manual, or the existing operator fails intermittently and replacement parts for that older unit are no longer available.
What it costs in Rialto
Automatic gate installation in Rialto typically runs $2,500 to $6,500 when the job includes a new operator, safety edges, and control wiring.
How we do it
We lay out the opening, pour reinforced footings below the soil’s shift line, hang the gate and operator, wire the control board, install safety edges and photo eyes, and cycle-test until the system closes cleanly without binding.
Driveway Gate Installation
Signs you need it
The existing driveway gate sags visibly, scrapes the ground when opening, or has rusted through at the hinge and post connections.
What it costs in Rialto
A new driveway gate installation in Rialto typically costs $1,800 to $4,800 for most steel or iron gates on standard widths.
How we do it
We remove the old gate, inspect existing posts for rust or movement, reset or replace posts as needed, fabricate or source the new gate, hang it, test travel clearance, and adjust the sweep so the gate rides level through its full range.
What Gate Installation Costs in Rialto
| Item | Typical range in Rialto |
|---|---|
| Manual gate fabrication and install | $1,800 – $4,000 |
| Automatic operator added to gate | $1,200 – $2,500 |
| Complete automatic driveway gate system | $2,500 – $6,500 |
Do you handle the electrical run for a new automatic gate?
Yes. We run the low-voltage control wiring and power to the operator, including conduit and connections to your existing panel. The work is done to code and tested before we hand the system over.
How long does a gate installation take in Rialto?
Most installations take two to four days once materials arrive. Custom gates add fabrication time, and we’ll give you a schedule in writing before any work begins. Call (844) 703-6053 for a free estimate.
Brands We Service in Rialto
We work on the gate brand you already have. That includes Viking, Ghost Controls, DoorKing, and Elite systems, among others. We keep common control boards, sensors, and receiver parts stocked for faster diagnosis in Rialto, and most electrical repairs are completed on the first visit. See our brands for the full compatibility list.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Rialto, CA
| Service | Typical range in Rialto |
|---|---|
| Hinge replacement or re-weld | $150 – $450 |
| Sagging gate correction | $250 – $700 |
| Post re-setting or reinforcement | $300 – $800 |
| Opener motor replacement | $450 – $1,200 |
| Control board replacement | $350 – $900 |
| Sensor or photo eye repair | $150 – $400 |
| Manual gate fabrication and install | $1,800 – $4,000 |
| Complete automatic driveway gate system | $2,500 – $6,500 |
Prices in Rialto push toward the upper end when the original posts are too far gone to reuse, when the ground has shifted enough to require deeper footings, or when custom width fabrication is needed. Every job gets a written price agreed before any work starts, so the number on the quote is the number you pay.
Neighborhoods We Serve in Rialto
We work across both Rialto ZIP codes, from the older blocks near downtown to the newer tracts along the northern edge of the city. Response for repair calls is typically same-day or next-day depending on call volume, and installation measures are usually scheduled within a few days.
- Las Colinas
- North Rialto
- Downtown Rialto
- Renaissance
- Sunrise
Service Area – Cities Near Rialto
Manor Gate Repair serves Rialto and the surrounding Inland Empire communities. We regularly work in Bloomington, CA, Fontana, CA, Muscoy, CA, and San Bernardino, CA. The same crews and the same brand-agnostic parts stock cover all of these areas.
Serving Rialto, CA — Our Local Coverage Area
We’re based in the Rialto area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Rialto
Most residential gate repairs don’t require a city permit, but new installations involving electrical or substantial structural work sometimes do. We check Rialto’s current requirements as part of the quote and handle the permit process when one is needed.
In most cases, yes. We schedule free on-site measures in Rialto within a few days of your call, and we give you a written price before any work is scheduled. Call (844) 703-6053 and we’ll set a time.
No trip fee for estimates on installation work. We give you a free measure and written quote whether you’re in the 92376 or 92377 ZIP code. Repair calls are quoted as a flat job price before work begins.
What happens when you call
- 1A real person answersNo phone trees — talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you — the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Rialto Customers Say
"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
— Megan Delaney"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
— Tracy Mercer"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
— Daniel Thompson